veneering

英 [vəˈnɪərɪŋ]

美 [vəˈnɪrɪŋ]

网络  镶饰; 薄片贴花; 镶面; 薄片贴面

现在分词：veneering　

英英释义

noun

• the act of applying veneer
• coating consisting of a thin layer of superior wood glued to a base of inferior wood
  Synonym:veneer

双语例句

• Objective To investigate the interface bond strength and compatibility between High-Strength Dental Ceramic ( type A) and Vintage AL veneering porcelain.
  目的考察高强度牙科陶瓷（A型）与松风VintageAL饰面瓷之间的界面结合及匹配性，为其临床应用奠定基础。
• The bulges in veneering are mainly caused by the factors such as uneven surface, drying speed of glue, moisture content of veneer.
  分析了薄木贴面工艺中，木皮起泡主要是由于表面不平、胶水固化程度和薄木含水率等原因所致。
• Taking a project as the example, this paper briefly introduces construction preparation, technical process, technical organization and quality control of veneering enamelled bricks on tall building's exposed wall with large area.
  以某工程为例，简要介绍了高层建筑外墙大面积釉面砖粘贴的施工准备、施工工艺流程、施工技术组织措施及质量控制措施。
• AIM: To assay the influence of repeated firings on the color stability of the glass infiltration alumina core ceramic and veneering porcelain complex and to provide experimental basis for clinical application.
  目的：测定烧结次数对渗透铝瓷-饰面瓷复合材料颜色稳定性的影响，为临床实际应用提供实验依据。
• AN EXPERIMENT ON INARCHING BY INLAYING A STALK ON ROOT PRUNING STALK OF CUCUMBER Study on Veneering with Two-Solution Adhesives
  黄瓜砧木断根靠接法试验研究两液胶薄木饰面工艺初探
• The technique of hot-pressed veneering ceramic was recommended to be used on the surfaces of zirconia and metal core crowns, to reduce the inner defects of veneering ceramics and to improve process efficiency. 3.
  临床上氧化锆、金属合金内冠表面可使用热压铸饰瓷工艺，既降低饰瓷材料缺陷，又提高饰瓷工艺效率。
• An investigation has been made on veneering with two-solution adhesives consisting of urea formaldehyde resin adhesive and polyvinyl acetate resin adhesive.
  本文探讨了用脲醛树脂胶与聚醋酸乙烯酯乳液组成的两液胶薄木饰面工艺。
• The mainly failure reasons were: veneering chipping and delamination, secondary caries and so on.
  主要失败原因有：饰瓷剥脱、修复体边缘的继发龋的发生等。
• By analyzing the different conditions in each period of veneering, the methods of how to mend bulges were given.
  并对各个阶段出现起泡的具体情况进行分析，给出处理方法。
• In this study, using an all-ceramic core material ( MIC), we investigate the change of strength caused by sandblast under different grain size, pressure and time. We also research the strength change of MIC sintering with its veneering porcelain that has been sandblasted before.
  本研究选用全瓷修复底层材料（MIC），通过改变喷砂的粒度、压力和时间，研究喷砂对其强度的影响，并对喷砂后的试件进行饰面瓷烧结，测量其强度的改变。