spattering

英 [ˈspætərɪŋ]

美 [ˈspætərɪŋ]

v.  溅; 洒; 洒落; 滴滴答答地落下
spatter的现在分词

机械

BNC.46335 / COCA.40518

柯林斯词典

• V-ERG 溅;洒
  If a liquidspattersa surface or youspattera liquid over a surface, drops of the liquid fall on an area of the surface.
  1. He stared at the rain spattering on the glass...
     他凝视着雨点溅落在玻璃上。
  2. Gently turn the fish, being careful not to spatter any hot butter on yourself...
     轻轻地把鱼翻过来，小心别把滚烫的黄油溅到自己身上。
  3. Blood spattered the dark concrete...
     鲜血溅落在黑色的水泥地上。
  4. I always spatter my blouse with gravy when I eat...
     吃饭的时候，我总是把肉汁溅到衬衣上。
  5. Her dress was spattered with mud.
     她的裙子溅上了泥浆。

英英释义

noun

• the act of splashing a (liquid) substance on a surface
  Synonym:spattersplashsplashingsplattering
• the noise of something spattering or sputtering explosively
  1. he heard a spatter of gunfire
  Synonym:spattersplattersplatteringsputterspluttersputtering

双语例句

• The carcass hit the cobbles so hard that it burst open, spattering her lower legs with entrails and maggots.
  尸体狠狠地摔在鹅卵石上，以至于猛地被撞散，溅了她一小腿的内脏和蛆虫。
• The experiments indicate that the CO2+ Ar mixed gas shielded welding can improve the external and internal quality of weld and the mechanical properties of joints, as well as reduce the spattering.
  本文通过试验表明CO2+Ar的混合气体保护焊具有改善焊缝外观和内在质量，减少飞溅，提高接头机械性能等特点；
• Mind that brush, you're spattering the floor with paint.
  当心刷子，你把地板上都溅上油漆了。
• It is proved that the new control method can obviously reduce the spattering loss, improve the weld formation and broaden the criteria of the optimum welding conditions.
  新控制法可以明显地减小飞溅，改善焊缝成形和扩大合理的焊接规范区。
• Rain drops were spattering on the doorsteps.
  雨点洒落在门阶上。
• He stared at the rain spattering on the glass
  他凝视着雨点溅落在玻璃上。
• Rain drops were spattering on the doorsteps. press ( down) the accelerator of a car
  雨点洒落在门阶上。踩（下）汽车的油门
• It is shown by the experiments the spattering is mainly caused by the explosion of metallic bridge at contacting points in momentary short circuiting.
  试验表明，该区的严重飞溅，主要是在瞬间短路时，接触点处金属液桥的电爆炸造成的。
• Based on analysis of the principle of electrode over-burning and spattering during aluminum alloy spot welding, one new electric current control method is presented.
  在分析铝合金点焊过程中电极烧损与飞溅机理的基础上，提出了一种新的电流控制法。
• By the dimension analysis, the relation of spattering distance to touchdown impulse and contact length of chimney body to the ground was established.
  通过量纲分析，建立了飞溅物距离与烟囱触地冲量以及烟囱与地面接触长度的关系。