看词语>英语词典>abrading翻译和用法

abrading

英 [əˈbreɪdɪŋ]

美 [əˈbreɪdɪŋ]

v.  磨损(岩石等); 擦伤(皮肤等)
abrade的现在分词

化学

柯林斯词典

  • VERB 磨损;磨蚀;擦伤
    Toabradesomething means to scrape or wear down its surface by rubbing it.
    1. My skin was abraded and very tender.
      我擦破皮了,一碰就疼。

双语例句

  • The results showed that after being processed on numerical control lathe, grade polished by SiC micro-powder and diamond abrading agent and size corrected by special tools, the Al_2O_3 ceramic hip joint femur ball has good surface degree of finish and it matches well with the femur handle.
    结果表明,通过数控车床车削、SiC超细粉和金刚石研磨膏分级抛光并用特制工具修正其尺寸,可以得到具有一定表面光洁度并与股骨柄配合良好的Al2O3陶瓷髋关节股骨头假体。
  • Noting the following device can effectively cut an abrading of cluth.
    注意以下方法可以有效减少离合器的磨损。
  • On-Line Roll Grinder ( ORG), as the principal part of the techniques of working roller abrading uniformity, consists of On-Line Profile Measure ( OPM) and Grinder.
    作为工作辊磨损均匀化技术中的主体-在线轧辊修磨装置(On-LineRollGrinder-简称ORG)由轧辊辊型轮廓在线测定仪(On-LineProfileMeasure-简称OPM)和修磨装置组成。
  • The diameter of the abrading section is required to be measured for abrasion analysis of the drill pipe. The traditional contact measurement is unefficient and has big human error.
    在石油钻井中,对钻杆的磨损分析需要测量磨损部位的直径尺寸,传统的接触式测量方法效率低,人为误差大。
  • Pointing to the real time monitoring and control of small circular vibration of the main vibration platform in graphite electrode abrading machine, the vibration of the main vibration platform in X, Y axis is detected by a eddy transducer with two probes.
    针对石墨电极研磨机主振台微圆周振动轨迹实时监测与控制的要求,采用了双测头电涡流传感器分别检测主振台X、Y向的振动。
  • By adjusting the lateral bolts, the clearance that is caused by abrading between the die sleeve and the guiding sleeve will be eliminated.
    当压边模套与导套之间因磨损产生间隙时,借助调节设在侧面的调节螺栓,便可消除产生的间隙;
  • Study ON The Magnetic Electrolytic Abrading Process And Machine In Curved Container
    曲面容器磁力电解研磨工艺及机械的研究
  • In order to customise the test to your requirements, choose from a wide variety of abrading wheels and abraser accessories to simulate real-life wear conditions.
    为了自定义的测试您的要求,选择从磨石配件种类繁多的研磨轮,以模拟真实的磨损情况。
  • Reduce to small pieces or particles by pounding or abrading.
    通过重击或磨损使变成小的碎片或颗粒。
  • The composition, consisting of hard and soft polishing agent, densifier, abrading agent and solvent, of a polishing wax for cars was analyzed by infraed spectra.
    采用红外光谱法分析一种汽车上光蜡组成分,包括硬蜡和软蜡上光剂、增稠剂、研磨剂和溶剂。